Windows 7 stuck in basic mode
So, the question here is: what should you do when Windows 7 stuck at loading screen? We believe there are many suggestions mentioned on the internet to cope with this problem, however, you have no idea whether they are credible or not. With that in mind, we have filtered feasible solutions for users to refer to. Start Windows in Safe Mode , and then restart your computer as usual. Yes, you read that right, just start Windows 7 in Safe Mode and then restart your computer without doing anything in Safe Mode.
The reason for doing so is that sometimes Windows updates or something else gets hung up. In this case, a forced restart won't get work.
But if you try it from Safe Mode, miracle happens sometimes. In the command prompt window, run bootrec. This should be helpful.
Or you can also do like this: Insert the Windows installation CD. Then it will load drivers and the screen should pop up to go on installing Windows.
Click that option and it should fix the problem. If you have made full system backups in daily usage, things will become very easy. You can restore the system to a time when it works. Step 1. Start Windows 7 normally. Before you see the Windows loading logo, press F8 on your keyboard. Then you can see a variety of Advanced Boot Options.
Step 2. Choose Repair Your Computer and wait until Windows 7 repair mode is ready. Step 3. If you are told to choose keyboard, just click OK. If you are told to choose an account, choose your account, and click OK.
If you have set password for your Windows account, enter the password too. Then you can see System Recovery Options. Step 5. Here you can see all Windows restore points available. Try your best to recall when your computer is safe and sound, and choose the corresponding restore point.
If you do not see the full restore points, check Show more restore points. Step 6. Click Next. It will try restoring your Windows to the restore point you have selected. This will take some time before the system restore is done. Hope this helps. Turn on your computer, and before you see the Windows loading logo, rapidly press F8 key on your keyboard. Choose Repair Your Computer and wait until Windows 7 repair mode is started.
If it asks you to choose a keyboard, just click OK. If it tells you to choose an account, choose your account, and click OK. If you do have password for your Windows account, you need to enter it too.
Choose Command Prompt , this will run Windows command prompt. This will scan your hard drive for errors, and will try to fix the errors if it detects any. This process can take some time so please wait until the disk check is done. However, if the same situation happens, this means there is a certain issue for the hard drive.
Then you should consider replacing it. Buy Now. Then set computer to boot from the bootable media in BIOS. After that, copy the whole disk to another one. In this way, you won't lose any data in the source disk if anything bad happens. Step 2: Choose a target disk to hold all content of the source disk. Note that all data on the target disk will be cleaned so be sure that this drive can be cleaned or a backup has been made in advance.
Step 3: Choose a copy option here. You can keep the original partition size, keep the proportion of the partition sizes, or customize the partition size of each partition. Besides, here are two options for you:. Follow the steps below:. Step 1. Type cmd in the Run dialogue and press Enter. Step 2. In the Command Prompt window, type the following commands and press Enter after each to stop Windows Update service and then restart it:.
Step 3. Type exit and press Enter to close Command Prompt. Tips: If you still get stuck on Welcome screen Windows 7, rename a few files and restart your computer again. Therefore, to fix Windows 7 stuck on Welcome screen, you can follow the instructions below to check and repair corrupted files. Type exit and press Enter to close Command Prompt and restart your computer.
The Startup Repair tool can repair Windows by replacing important operating system files that might be damaged or missing. Then follow the instructions on the screen to complete the repair. This issue can also be caused by one of the non-Microsoft applications or a driver. If you are able to boot successfully in Safe Mode, you can perform a clean boot to find the root cause. Click Start , type msconfig in the Start search box, and then press Enter. Under Selective Startup , click to clear the Load Startup items check box.
Step 4. Then click OK. Step 5. Click Restart when prompted. After the computer starts, check whether the problem is resolved. Tips: If your Windows 7 computer stuck even in Safe Mode, you have to turn to an installation media to boot and troubleshoot your computer. After fixing the issue Windows 7 stuck on Welcome screen, you need to take a serious consideration on how to prevent this issue or similar issues happening again.
Actually, the best and easiest way is to make an image backup. A backup is almost zero cost, and it can help you to solve all kinds of system issues by restoring to the previous good state from the backup. It is totally free! Click the button below to download this freeware:.
Then choose a destination path to save the backup, and finally click Start Backup. For example, you can restore system to a dissimilar hardware, backup dynamic disk volume , and automatically delete old backups, etc. Now you know how to fix Windows 7 stuck on Welcome screen. Scenario: Windows 7 stuck on Welcome screen "I boot my computer, and get to the Windows Welcome screen after I enter my password, the spinning loading thing rotates forever.
0コメント